You are here: Home > Garage Door Springs > Standard Garage Door Torsion Springs

Torsion Spring Special! Save 40% on the most common spring sizes!

Standard Garage Door Torsion Springs

---

---

To buy standard garage door torsion springs go directly to our torsion spring prices at the bottom of this page.

We currently stock 1 3/4," 2," 2 1/4," and 2 5/8" ID torsion springs and cones for residential doors. For all other types of springs go to our Garage Door Springs page. For an engineer's perspective on torsion springs we recommend you visit Richard Kinch's page titled "How I Replaced Deadly Garage Door Torsion Springs And lived to tell the tale." He has a lot of helpful information and engineering formulas there.

To assure you are ordering the correct springs, read or review this page. The extra time should prove beneficial. Over the years we have discovered that informed customers are happier.

Standard residential torsion springs are found on a shaft above the center of the garage door. These springs typically come in 1 3/4", 2" and 2 1/4" inside diameters. If you have a broken torsion spring, read below to make the measurements you need, and then purchase a new garage door spring or springs.

Included below are a number of popular torsion spring topics, many of which you may want to consider before ordering a new standard torsion spring for your garage door.

Introduction to Standard Torsion Springs

A standard torsion spring has a stationary cone which secures the spring to the spring anchor bracket. Since this bracket is secured to the wall, the stationary cone, as its name suggests, does not move. The other end of the torsion spring has a winding cone. This winding cone is used when installing, adjusting, and uninstalling the springs. When installing the torsion spring, the coils of the spring are wound up to create a lot of torque.

This torque is then applied to the shaft, the metal tube that goes through the torsion spring. The ends of the shaft are held up by the end bearing plates. Resting against the race of the bearings are the cable drums. The cable wraps tightly around the cable drum, and the cable goes down to the bottom of the garage door, securing to the bottom bracket.

Since these cables hold the weight of the garage door, the torque from the torsion springs does not dangerously spin the shaft until the spring is loose. Instead, the garage door weight slightly exceeds the lift produced by the torsion spring(s). (The lift is the amount of weight that each spring can raise off the ground.) As a result, a properly operating garage door with the right springs should not seem to weigh nearly as much as the garage door itself. When this principle holds true through the duration of the door's travel, the door is balanced.

With the help of the torsion springs, you should be able to operate the garage door manually without much trouble. Likewise, it does not take too much work from the garage door opener to lift the garage door. As the door opens (either manually or with the opener), the torque on the shaft keeps the cable tight on the cable drum. As a result, the cable winds up on the cable drum, allowing the torsion springs to unwind.

As the torsion spring unwinds, it loses some of its torque. Therefore, it also loses the amount of lift that it can produce. Vertical lift and high lift garage doors deal with this problem in a slightly different way, and you can read about How Vertical-Lift and High-Lift Garage Doors Work. Standard lift garage doors are almost universally used in residential garages and are in the majority in commercial and industrial settings.

It all comes down to the cable drums. Standard lift cable drums have a flat portion for the cable, with one or two grooves that are a little higher. (These higher grooves are addressed in the link above.) As the garage door opens, the rollers slide along the track. The door transitions from the vertical track to the horizontal track.

When the horizontal track supports the top section, each spring does not need to support as much weight. Since the springs have unwound a little by this point, the amount of weight supported by the horizontal tracks roughly equals the lift that was lost from the decrease in torque in the torsion springs.

When the garage door is fully open, there is still about 3/4 to 1 turn still applied to each torsion spring. Since the bottom roller on the garage door typically rests on the curved portion of the track, the door will want to fall down. The extra torque in the torsion springs, though minimal in comparison to the torque when the garage door is closed, keeps the door open.

Popular Torsion Spring Topics

Included below are a number of popular topics that interest homeowners when considering torsion spring purchases. Though it may be helpful to consider these options, they do not apply to all garage doors.

Replace Both Torsion Springs?

If you have two torsion springs on your door, you should replace both of them. Most doors have springs with the same cycle life rating. In other words, when one spring breaks, the other spring will probably break before too much longer. Since you will be going to the trouble of changing one torsion spring, it is usually better to change your second spring as well. This will save you time in the garage as well as money on the shipping costs.

Some doors, however, have two springs with different dimensions. Many times, the cycle life of the broken spring is shorter than the cycle life of the unbroken spring. This means that you may still have another couple thousand cycles left on your unbroken spring. If you only change one spring now, you will probably need to change your other spring fairly soon down the road. Therefore, we recommend that you still replace both springs, but that you purchase springs with the same length, inside diameter and wire size.

If this is the case, each of your new torsion springs will need to lift 1/2 of the total lift of your two old springs. A matched pair of springs can be determined for you by using our Unmatched Springs calculator.

For help determining whether you should replace both springs on your door, see our Torsion Spring FAQ's page. You can also read more about springs with different dimensions.

One Spring or Two?

A lot of people have a garage door with only spring on it and wonder whether they should upgrade to two springs. If the new torsion spring that you will install on your door has an inside diameter (ID) of 1-3/4" and a wire size of .250 or larger, we suggest that you convert to two torsion springs. The same holds true with a 2" ID and .2625 wire size or a 2-1/4" ID and .283 wire size.

The problem with having a larger wire size on a single-spring door is that the spring pulls on the shaft as the door opens and closes. This can cause serious problems in the future, including cables breaking or peeling off the drums and steel sections getting damaged. While it usually costs $5-$10 to convert over to two springs, it can save a lot of money down the road.

One question that people frequently ask when converting to two springs is whether they need a second bearing for the second spring. The answer is no. The purpose of the bearing is to keep the stationary cone centered on the shaft so that the spring is centered on the shaft. Since the stationary cones from the two springs will be secured to each other in the process of securing the springs to the spring anchor bracket, the second spring does not need a bearing. Additionally, adding a second bearing will probably break one or both of the stationary cones.

For more information to help you decide whether to have one spring on your garage door or two, see our One Torsion Spring or Two? page.

Different Spring Dimensions?

If your two spring dimensions are not the same, we recommend switching to a pair of springs with the same dimensions. While it is possible to use unmatched springs, you are more likely to get the maximum cycle life out of a pair of springs when they are the same length, wire size and inside diameter.

If you purchased two torsion springs with different dimensions, it is possible to maximize the cycle life on the two springs. See our Maximizing Cycle Life on Unmatched Torsion Springs page for more information.

If you currently have unmatched springs and wish to convert to a pair of matched springs, or if you want to read how to use unmatched pairs, see our Using Torsion Springs with Different Lifts page.

Longer Life Torsion Spring Options

The cycle life of a torsion spring refers the to rating regarding how many cycles (the door opening and closing is one cycle) the spring should make before it breaks. The cycle life rating does not account for premature breakage, often caused by chips in the steel or highly corrosive environments.

The standard cycle life in the garage door industry is 10,000 cycles. Spring under 10,000 cycles are considered overstressed and are not recommended for use. If you would like to have more than 10,000 spring cycles, your new torsion springs will need to have a larger wire size. The larger the wire, the longer it will take for the spring to break as thicker steel requires more bending before it breaks.

If you increase the wire size of your springs, you will also need to increase the length to keep the same lift and torque rating. On narrower, heavier doors it may also be necessary to increase the inside diameter to provide enough space on the shaft for the springs to fit.

When you search for a specific torsion spring, compatible springs with the same lift but a different cycle life will be listed. You can upgrade your torsion springs by purchasing one of these springs instead of spring matching your old dimensions. If you are browsing instead by door height, you can look under larger wire sizes to find a compatible spring with more cycles.

Spring Steel

We supply black coated, oil-tempered torsion springs. We don't recommend galvanized springs because they tend to lose more of their tension over time. If your door is in a highly corrosive environment, galvanized torsion springs may help to prolong the life of the springs. To prevent against premature breakage, we still recommend oiling galvanized springs as we do oil-tempered springs. For more information about galvanized and oil-tempered torsion springs visit our blog.

High Lift and Vertical Lift Conversions

A number of customers are interested in having their garage door open straight up before the top of the door rolls back toward the back of the garage. This type of door is called a High-Lift garage door. A vertical lift door never makes a transition to rolling backward - it just opens straight up. Both of these systems require higher ceilings.

To learn more about how these systems work, see our How Vertical-Lift and High-Lift Doors Work page. If you are interested in the work involved when performing a high-lift conversion, check out our High-Lift Garage Door Conversion tutorial.

If you are interested in converting your standard lift garage door to a high-lift door, please find the dimensions specified in the High-Lift Garage Door Conversion tutorial and fill out the form on our Garage Door High Lift & Vertical Lift Inquiry page. After filling out the form, you will see options for the spring cycle life for your conversion kit and the total cost; we will then contact you to complete your order.

Custom roofline lift conversion kits are also available. Most of these doors travel vertically for a foot or two before reaching the curved part of the horizontal track. Rather than rolling back parallel to the garage floor, the door instead continues to roll back and upward, following the pitch of the ceiling. This option is only available for garages with ceilings that pitch up and away from the door. These conversion kits are also available - visit our Garage Door High Lift & Vertical Lift Inquiry page to receive a quote for a custom roofline high-lift kit.

If you have enough space in your garage for your door to open vertically and are instead interested in a custom vertical-lift conversion kit, please contact us so we can determine the parts you need and the cost of your new kit.

Buy Standard Residential Garage Door Torsion Springs

Follow the instructions below to make the proper measurements when looking to buy new torsion springs. Once you have your measurements, you can contact us or use our Find My Spring Database™ and the bottom of this page to order new springs.

Measuring Your Garage Door

There are three different methods for determining what torsion springs you need for your garage door. You can 1. Measure your existing springs, 2. Weigh your door with an analog scale, or 3. Determine the manufacturer and model number.

If your garage door was balanced before your spring broke, you can measure your springs. If you are not especially skilled with a ruler or if your garage door was not balanced, we suggest that you weigh your door with an analog scale. If this is not an option for you or if you would prefer our help in determining your door weight, you can find your door manufacturer and model number.

Regardless of the method you choose, you will need to determine your cable drum number. This number gives the diameter of the cable drum. If you do not have a 4" diameter drum, you will have to contact us with the information you gather when you choose one of the three methods so you can order new springs.

You will also need your track radius. As pictured, this is the radius of the curved portion of your horizontal track. While this varies from door to door by only a few inches, a larger track radius requires more turns on the spring and therefore slightly increases the lift of a spring while slightly decreasing the cycle life rating.

Your door height will also be a necessary dimension when finding new torsion springs.

Method 1: Measure your existing springs

Method 2: Weigh your door with an analog scale

Method 3: Determine the manufacturer and model number

Special Orders

If you do not have a 4" diameter cable drum, you will need to contact us so that we can determine the springs you need.

If you have a high-lift or a vertical-lift garage door, our database will not give you accurate spring information. If you can find an exact replacement spring in our database, it will work. Because of the extra turns required on the spring for the lift design, the cycle life will not be accurate. If you are instead finding new springs from your door weight, you will have to contact us so that we can find replacement springs for your system.

If your garage door is greater than 8' tall, please contact us so that we can find replacement springs for you.

If you cannot find your current spring in our Find My Spring Database™, your spring may be overstressed for your door height. Many manufacturers and installing garage door companies are cutting corners and installing garage door springs with cycle lives that fall below the 10,000-cycle industry standard. Try changing your door height to 6' 6". If you then see the spring, consider using one of the suggested cycle life upgrades for the 6' 6" high door for your taller door. If you can't find it there contact us. We will find their torque ratings and recommend suitable higher cycle replacements. We may also ask questions about your garage door to make sure your measurements are correct. We will sell springs rated below the 10,000-cycle minimum, but we will not accept returns on any of these springs.

Purchase Standard Torsion Springs with our Find My Spring Database™

Garage Door Torsion Springs are normally centered above the garage door on a one inch shaft. At one end of the spring is the winding cone that is secured to the shaft with set screws. At the other end of the spring is the stationary cone. This is secured to the spring anchor bracket, which is secured to the header. On two-spring assemblies the stationary cones of both springs are mounted back to back to the spring anchor bracket. The shaft running through the springs transfers tension from the springs to the cable drums at the end of the shaft. These drums pull on the cables, which pull on the bottom of the door to balance the weight of the garage door.

Our database below is based on garage doors utilizing 4" diameter cable drums with 12.6" circumferences on the flat portion. The most common 4" cable drums are marked with the following identifying numbers: WD-4, WD-4X, 400-8, 400-9, OMI-8, DNS-4X-8, D400-96, 1000, 1001.

This database includes prices, lifts and cycles for garage door torsion springs with 1 3/4," 2" and 2 1/4" inside diameters. Raynor springs often measure to be 2 1/8" or 2 3/16" but you will need to order them as 2 1/4". Do not order 2 1/4" ID springs unless you have a Raynor Garage Door because there may be hardware compatibility problems.

All the residential torsion springs we provide are wound with 1/2" rods, usually 18 inches. You can buy 1/2" X 36" rod at almost any hardware store and cut one in half. If you would like for us to include a pair of winding rods in the order you can follow the links at our Garage Door Tools & Technical Support page.

Customers have also asked us about whether they should replace their cables, end bearing plates and center bearings. Cables normally don't need to be replaced. It would be good, however, to check for frays along the length of each cable and for rust at the bottoms if they are subject to salt corrosion. If needed, you can purchase new cables on our Garage Door Cable and Fittings page. The end bearing plates rarely need to be replaced. The Chinese made some bearings several years ago stamped with the letters "ADH." These, along with some of the old McKee Door end bearings are about the only ones we've seen wear enough to warrant replacing. It is even rarer when a center bearing needs to be replaced. In our experience it's probably only one in 5,000 or more spring replacements where a new bearing would be needed. That's usually only on center support brackets that were not installed plumb or perpendicular to the header. A drop or two of oil is usually all that most center bearings ever require. If needed, you can purchase these parts on our Garage Door Bearings & Bushings page.

EZ-Set Springs: Do NOT use this database

Commercial Torsion Springs

Overhead Door Cones

Shipping Times

Returns

Order Garage Door Springs with Confidence!

Winding Bar Special - $15 Value for a Penny!

For this special offer click here or the link above and order the bars before ordering the custom springs. If you skip this step please let us know in the comment section that you would like the free winding bars. This price applies only to orders for standard torsion springs in the database below. No other substitutes are available. Offer applies only to parts shipped to any of the 48 contiguous United States. In some parts of the country our cart adds extra for shipping. If this occurs, remove the bars from the cart and add this note to the comment section of your order form: "Please provide free winding bars with this order."

Same or Next Day Shipping - No Extra Charge!

Place your order by noon central time for same or next day business shipping on most of the 6,000 springs below for residential and light commercial sectional overhead garage doors.

Torsion Spring Specials! - Save 50% on Pre-Cuts!